Every place that surfaced a FAILED SAT result — task error messages,
component-status.json detail, and the hardware snapshot's ErrorDescription/
StatusHistory — used to say only "SAT overall_status=FAILED (see
summary.txt)" or "<label> failed", forcing an engineer to go dig through the
run directory to find out what actually broke.
nvidia-config's summary.txt now carries a "warnings" field with the specific
GPU/NVLink finding. A new SATFailureDetail/satFailureDetailFromKV in
component_status_db.go reads that field, or falls back to naming whichever
generic SAT sub-job(s) reported non-OK/UNSUPPORTED status along with their
exit code. This feeds both the task-runner error message and the component
status DB. sat_overlay.go's satKeyStatus (which drives ErrorDescription on
the exported hardware snapshot) now does the same, with storage kept
per-device so one drive's rc doesn't get attributed to another's card.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The standalone "confidential-computing" SAT target only ever checked CC
readiness, which most fleets never opt into (a NOT_READY verdict there
isn't a fault). Meanwhile DCGM diag never asserts GPU config compliance
(ECC/MIG/power-limit vs factory default) or NVLink topology (per NVIDIA's
own DGX BasePOD deployment guide, this needs a separate validation step)
— gaps confirmed against public DCGM docs and a real NV17-vs-expected-NV18
bonded pair found on a live bundle.
Repurposes the routine into "nvidia-config": reuses the existing
ListNvidiaGPUSettings() (already backing the GPU-settings page) to flag
ECC disabled, a MIG mode change stuck pending a reset/reboot, and a power
limit capped >5% below default; parses "nvidia-smi topo -m" bonded pairs
against "nvlink -s/-e" to flag any inactive lane or nonzero replay/
recovery/CRC counter on an otherwise-active bond. CC readiness is folded
in as one informational field (does not gate overall_status) rather than
a dedicated test. Reports under the same pcie:gpu:nvidia severity key as
every other nvidia-* SAT target instead of an isolated key, so a
config/NVLink FAILED result isn't invisible next to stress-test results.
Also fixes ApplySATResultToDB silently dropping any target with no
matching switch case (exactly what the old confidential-computing target
did) with a new coverage test enumerating every real SAT target.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
/topo blocked the HTTP request on live nvidia-smi calls with no timeout
(topo -m, nvlink -s/-e run on every page load), so a wedged driver hung
the page indefinitely. CaptureTechnicalDump now persists these dumps
once per audit cycle; the page reads them from techdump/ instead.
buildSocketIndex mapped NUMA node number to CPU by treating dmidecode's
Socket Designation (often 1-indexed, "CPU1"/"CPU2") as equal to the
NUMA node number (always 0-indexed) — GPUs/NICs on NUMA node 0 fell
into the "unknown" column, others attached to the wrong CPU box. Now
ranks CPUs by Socket value instead of assuming a shared numbering base.
Fixed a bug in ComponentStatusDB/applyComponentStatusDB where GPU SAT
results were keyed per-target ("pcie:gpu:nvidia-stress") instead of
per-vendor, which both broke cross-tier severity tracking (a later
clean "2. Check" run and an earlier failing "3. Load" run never
compared severities) and silently failed to match any real BDF, so the
DB overlay never reached the topology graph at all. GPU keys are now
normalized to vendor ("pcie:gpu:nvidia"/"pcie:gpu:amd"). Also skip
writing to the DB when a SAT task was aborted by the user (ctx
canceled), so a partial run can't stomp a previously recorded status.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
New read-only "Check" step reports whether this server can run NVIDIA
Confidential Computing: CPU TEE support (Intel TDX / AMD SEV-SNP, via
dmesg and kvm_amd sysfs params) and GPU firmware CC capability (via
`nvidia-smi conf-compute -q`). Also collect that command's output into
the techdump export bundle.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
RAID Controller Management previously hid any LSI drive that wasn't
already Frgn/UGood/JBOD, and scoped VROC "free drives" from all system
disks instead of the ones actually wired to the VROC controller's
ports - drives attached directly to the CPU or another HBA could leak
in. Now every drive is listed per its own controller, and LSI drives
not already ready for array creation get a "Prepare" button that
forces them to Unconfigured Good via storcli.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Replaces separate IPMI FRU and SAA DMI cards with a single FRU / Elabel
card that reads all available sources in parallel and shows each field
with a color-coded source chip (IPMI FRU / Huawei iBMC / SAA DMI).
Huawei elabel fields are read/written via OEM IPMI raw commands
(NetFn 0x30, cmd 0x90) with 19-byte chunking protocol, matching
the FusionServer ElabelTool V511 wire format. Covers DeviceName,
DeviceSerialNumber, ProductName, ProductSerialNumber, ProductAssetTag,
ProductManufacturer, MainboardManufacturer, BoardProductName,
ChassisPartnumber, ChassisType (read-only), IOChassisSerial,
IOChassisAssetTag, and GUID (read-only via standard 0x06 0x08).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Unified card for LSI/Broadcom and Intel VROC controllers: auto-detects
foreign configurations and warns the operator with Import/Clear actions;
allows creating RAID 1 mirrors from unconfigured drives regardless of
controller type. Live output streams via SSE into an inline terminal.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds a new card to the web UI Tools page for reading and editing DMI
fields via SAA (In-Band). Reads current DMI configuration with GetDmiInfo,
displays all fields as an editable table, and applies only the changed
fields via EditDmiInfo + ChangeDmiInfo. Backs up the original DMI file to
dmi-backups/ before any write, making it available in the support bundle
for rollback. Also adds "saa" to the standard tool check list.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
mchus