- GPU load switches from bee-gpu-burn (compute burn, ~88% TDP) to
dcgmproftester -t 1004 / targeted_power via
resolveBenchmarkPowerLoadCommand — the same engine Power/Thermal Fit
uses and the hottest sustained NVIDIA load we have, so fans are
actually pushed toward their ceiling.
- Sample loop is now IPMI-hang-proof: every ipmitool read is time-boxed
in an abandonable goroutine, and the poll interval backs off
geometrically (1s→30s) when reads are slow, tightening again on
recovery. A plateau is only trusted while telemetry is healthy;
degraded runs ride out to MaxLoadSec. Summary gains fan_samples /
telemetry_degraded. Drops the per-second nvidia-smi+power+cpu-temp
sampling from the hot loop.
- Dead code removed: FanStressRow, GPUStressMetric, sampleFanStressRow,
sampleGPUStressMetrics, WriteFanStressCSV/WriteFanSensorsCSV,
analyzeMaxTemp, sampleSystemPowerResolved.
Topology fan tiles:
- size encodes the fan's ceiling RPM (its class), not current speed;
coloured fill rising from the bottom encodes live duty cycle
(current / ceiling), shown only when the ceiling was measured.
- glyph spin rate now maps absolute RPM into a human-perceptible band
(fanSpinPeriodSec: 2.2s/turn at <=1000 RPM, 0.35s at >=13000).
- the "N fans · N OK · tile size ∝ …" caption line is gone.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019VHG21rgTUiR1G3qFHTVmN
Repurpose the previously-unwired RunFanStressTest into RunFanCheck, a
Load-tier SAT test that drives stressapptest (CPU+memory) and, when a GPU
is present, a GPU burn to 100% simultaneously, then watches every fan
until none has climbed for ~60s. The observed peak RPM per fan is the
"ceiling"; it is persisted through the existing fan-observation store.
MSI G4201 / AMI MegaRAC exposes no host-side fan force (every OEM IPMI
command returns 0xc1; Redfish Thermal is GET-only), so load-driven ramp
is the closest safe equivalent. See
bible-local/decisions/2026-09-04-fan-ceiling-check.md.
- platform.ResolveFanMaxRPM: per-fan max with fallback (persisted peak ->
peer peak -> current RPM), resolved in platform, not the view.
- platform.ErrTestNotApplicable: no load source or no fan sensors ->
task lands as cancelled ("not applicable"), never failed, so an
engineer never sees a false red. executeTaskWithOptions maps the
sentinel; finalizeTaskForResult honours a pre-set TaskCancelled.
- Verdict FAIL only for a fan at 0 RPM / IPMI cr-nr under load.
- /topo: one small spinning square per fan, sized by RPM / resolved max,
clickable through to a new "fan" component-detail type; per-fan status
recorded to the component-status DB from the fan SAT summary.
- Wiring: /api/sat/fan/run route, "fan" task target, Load-page card,
stress-mode Run All.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019VHG21rgTUiR1G3qFHTVmN
NVIDIA GPUs deliberately downclock PCIe to Gen1 at idle for power
saving, and applyPCIeLinkSpeedWarning fired on every idle collector
pass regardless - since component-status DB records never downgrade
(Record() only ever raises severity), one boot-time idle sample
permanently pinned pcie:gpu:nvidia to Warning for the rest of the
session even after every load-bearing GPU SAT test passed clean. Two
prior fixes (nvidia-smi-sourced link speed, pcie_aspm=off boot flag)
didn't hold up against this hardware/driver combination - see
bible-local/decisions/2026-08-24-pcie-gpu-gen1-idle-warning.md for the
full history.
Rather than add a downgrade path, stop writing an unverified status in
the first place: parseLspciDevice no longer calls
applyPCIeLinkSpeedWarning on the idle path. LinkSpeed/MaxLinkSpeed stay
populated as plain descriptive fields; only a verified-under-load
caller may now turn them into a status verdict.
Two new SAT targets provide that verified signal:
- pcie-link (platform/pcie_link_check.go): forces every enabled PCIe
device - not just GPUs - to retrain via the PCIe spec's Link Control
"Retrain Link" bit, then compares the negotiated speed against the
device's max. Covers NICs/HBAs/switches that have no bee-gpu-burn
equivalent load tool. Classifies by PCI class code + vendor ID, not
name substrings. Routes gpu_nvidia/gpu_amd/other sub-verdicts into
their own component-status keys so a degraded NIC never reads as a
GPU fault.
- nvidia-pcie-bandwidth (platform/nvidia_pcie_bandwidth.go): drives
real host<->device traffic via dcgmi diag -r nvbandwidth and
resamples link speed immediately after, independent of nvbandwidth's
own pass/fail.
Both wired into the task queue/webui the same way as nvidia-config
(routes, dispatch, priority, Validate page cards, Run All Check SAT).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
pci=realloc was forcing a full PCI resource reallocation on every default
and toram boot, added as a GPU BAR workaround for BIOS without Above 4G
Decoding. On a dense NVMe-backplane server it exhausted MMIO32 space and
silently dropped 4 of 6 NVMe controllers from the OS even though the BIOS
and lspci both saw them fine. It now only applies to the no-GUI/gsp-off
troubleshooting entry, alongside a bible-local ADR for the two prior
rounds of SAT/blackbox durability work.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Disabled PCIe devices (sysfs enable==0) carry no data traffic; their
link state has no operational impact. Switchtec PCIe switch management
endpoints on NVIDIA HGX H100 baseboards (and similar fabric controllers)
train at reduced speed intentionally and were producing spurious warnings.
Check is vendor-agnostic: reads enable attribute via existing helper,
no vendor/device ID hardcoding.
Documented in bible-local/decisions/2026-06-12-pcie-disabled-device-link-warning.md.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- nvidia collector: read pcie.link.gen.current/max from nvidia-smi instead
of sysfs to avoid false Gen1 readings when GPU is in ASPM idle state
- build: remove bee-nccl-gpu-stress from rm -f list so shell script from
overlay is not silently dropped from the ISO
- smoketest: add explicit checks for bee-gpu-burn, bee-john-gpu-stress,
bee-nccl-gpu-stress, all_reduce_perf
- netconf: re-exec via sudo when not root to fix RTNETLINK/resolv.conf errors
- auto/config: reduce loglevel 7→3 to show clean systemd output on boot
- auto/config: blacklist snd_hda_intel and related audio modules (unused on servers)
- package-lists: remove firmware-intel-sound and firmware-amd-graphics from
base list; move firmware-amd-graphics to bee-amd variant only
- bible-local: mark memtest ADR resolved, document working solution
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
