The fan-ceiling check, the webui metrics collector (every 5s) and the PSU
health poller each shelled out to ipmitool independently. The BMC's KCS
interface serializes those calls anyway, so under load the concurrent
`ipmitool sdr`/`dcmi power reading` invocations just queued behind each
other — that's what produced "IPMI slow" backoff during a fan-ceiling run in
a blackbox dump, while the dashboard looked fine only because it was reading
its own, separately-stale data from a different ipmitool call.
hw_telemetry.go is now the sole recurring poller (fan RPM, temperature, PSU
power/status, DCMI system power), with the adaptive 1s-30s backoff that used
to be duplicated inside the fan check. Every hot-path consumer reads the
shared cache (hwSnapshot / platform.HardwareSDRSnapshot) instead of calling
ipmitool itself.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Extract the fan peak-tracking into observedPeakStore (observe max under
load, hold >= minHold to reject spikes, round, persist JSON) and add a
second instance for PSU draw (psu-observation.json, keyed by PSU
ordinal). Fed from samplePSUPower like fans are from sampleFanSpeeds, so
any full-load run refines it — the Fan Ceiling Check (which also samples
PSU power at a slow cadence off its loop and writes psu_<i>_peak_w), a
burn, thermal cycling, and the 5s web metrics collector.
/topo PSU cards now scale the load fill by wattage_w when the BMC
reports it, else by the observed peak draw — marked "~N% load". This
MSI stand's BMC gives only instantaneous input power, so the observed
peak is the only capacity figure available.
Fan behaviour is unchanged (tests exercise updateFanObservation /
estimateFanDutyCyclePctFromObservation / ResolveFanMaxRPM through the
new store).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019VHG21rgTUiR1G3qFHTVmN
Each fan tile carries data-fan / data-ceil / data-measured and a small
script polls /api/metrics/latest every 5s — the metrics collector's own
sampling period, served from memory with no extra BMC call — updating
each tile's spin rate, duty fill and tooltip in place. Polling faster
would only re-read identical numbers; sampling the BMC faster would
choke it under load. FanReading gains json tags for the endpoint.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019VHG21rgTUiR1G3qFHTVmN
- GPU load switches from bee-gpu-burn (compute burn, ~88% TDP) to
dcgmproftester -t 1004 / targeted_power via
resolveBenchmarkPowerLoadCommand — the same engine Power/Thermal Fit
uses and the hottest sustained NVIDIA load we have, so fans are
actually pushed toward their ceiling.
- Sample loop is now IPMI-hang-proof: every ipmitool read is time-boxed
in an abandonable goroutine, and the poll interval backs off
geometrically (1s→30s) when reads are slow, tightening again on
recovery. A plateau is only trusted while telemetry is healthy;
degraded runs ride out to MaxLoadSec. Summary gains fan_samples /
telemetry_degraded. Drops the per-second nvidia-smi+power+cpu-temp
sampling from the hot loop.
- Dead code removed: FanStressRow, GPUStressMetric, sampleFanStressRow,
sampleGPUStressMetrics, WriteFanStressCSV/WriteFanSensorsCSV,
analyzeMaxTemp, sampleSystemPowerResolved.
Topology fan tiles:
- size encodes the fan's ceiling RPM (its class), not current speed;
coloured fill rising from the bottom encodes live duty cycle
(current / ceiling), shown only when the ceiling was measured.
- glyph spin rate now maps absolute RPM into a human-perceptible band
(fanSpinPeriodSec: 2.2s/turn at <=1000 RPM, 0.35s at >=13000).
- the "N fans · N OK · tile size ∝ …" caption line is gone.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019VHG21rgTUiR1G3qFHTVmN
Repurpose the previously-unwired RunFanStressTest into RunFanCheck, a
Load-tier SAT test that drives stressapptest (CPU+memory) and, when a GPU
is present, a GPU burn to 100% simultaneously, then watches every fan
until none has climbed for ~60s. The observed peak RPM per fan is the
"ceiling"; it is persisted through the existing fan-observation store.
MSI G4201 / AMI MegaRAC exposes no host-side fan force (every OEM IPMI
command returns 0xc1; Redfish Thermal is GET-only), so load-driven ramp
is the closest safe equivalent. See
bible-local/decisions/2026-09-04-fan-ceiling-check.md.
- platform.ResolveFanMaxRPM: per-fan max with fallback (persisted peak ->
peer peak -> current RPM), resolved in platform, not the view.
- platform.ErrTestNotApplicable: no load source or no fan sensors ->
task lands as cancelled ("not applicable"), never failed, so an
engineer never sees a false red. executeTaskWithOptions maps the
sentinel; finalizeTaskForResult honours a pre-set TaskCancelled.
- Verdict FAIL only for a fan at 0 RPM / IPMI cr-nr under load.
- /topo: one small spinning square per fan, sized by RPM / resolved max,
clickable through to a new "fan" component-detail type; per-fan status
recorded to the component-status DB from the fan SAT summary.
- Wiring: /api/sat/fan/run route, "fan" task target, Load-page card,
stress-mode Run All.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019VHG21rgTUiR1G3qFHTVmN
Every GPU-selection picker (Load/SAT, Burn, Benchmark) now renders the
card serial: "GPU N — <model> · <mem> MiB · sn: <serial>". The serial is
monospace and the digits that differ across the listed GPUs (common
prefix/suffix stripped) are emphasised so operators can tell cards apart.
Row markup was duplicated across three pages (and twice within
page_validate.go). Consolidated into a single module,
internal/webui/gpu_picker.go: beeGpuPicker.render({...}) builds every row;
gpuPickerCSS/gpuPickerJS are injected once by layoutHead/renderPage. Pages
keep their own selection-note text and multi-GPU toggles but no longer
hand-build <label> markup.
ListNvidiaGPUs() adds the serial via nvidia-smi --query-gpu=...,serial;
N/A is normalised to empty. Serial flows to the client unchanged through
the existing /api/gpu/nvidia JSON response.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01AudE3Q2nd9kxxVuxPKcTho
The techdump — the only place the IPMI FRU / Elabel identity (Product Name
= server model, serials, part numbers) is recorded — only ran under LiveCD.
Run it on every audit so `bee audit` on an installed host captures it too.
Also add `ipmitool mc info` and `ipmitool lan print` to the techdump, and
pin `ipmitool fru print 0` to FRU device 0 to match the Export Tools
"FRU / Elabel" editor exactly.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Rework the /topo diagram from side-by-side stacked cards into one tall
vertical bar per CPU socket with everything attached to it branching off
sideways (socket 0 left/branches right, socket 1 right/branches left).
Disks are now parented under the storage controller they physically hang
off (SATA/AHCI, SAS HBA, RAID) — itself a NUMA-affine PCIe device under one
socket — instead of a synthetic catch-all node. The disk->controller link
is read from a new storage-controllers.txt techdump
(platform.StorageControllerMapScript, a /sys/block walk); disks with no
resolvable controller fall back to an "Other" bar. No board/root node.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SYjrG6bVmeG1Z2Wmc8kg3o
The downstream-capability adjustment lowered f.MaxSpeed/f.MaxWidth to the
rate the endpoint supports, but the Degraded verdict still compared the
retrained speed against the stale local maxSpeed holding the bridge's own
uncapped capability. A Gen5 root port feeding a Gen4 HBA (or a Gen2 NIC)
was flagged DEGRADED even though the link ran at the fastest rate the pair
supports, failing the PCIe link check on healthy hardware.
Keep the local maxSpeed in sync with the peer-capped f.MaxSpeed so both
the pre-retrain and post-retrain verdicts use the real target.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Mx6AvuXcJNT7jx3jjWw4hc
pcie-link's retrain check compared post-retrain speed against a port's
max capability without checking whether anything was actually seated
downstream. A switch downstream port with no card plugged in retrains
to zero lanes but still reports a reset-state speed, so it was
misreported as "retrained to Gen1, capable of Gen5" — indistinguishable
from a real degraded link.
Now a port that was already empty before the retrain is skipped (same
treatment as a disabled device: legitimately unpopulated slots are
common and shouldn't fail the check), while a device that answered
before the retrain and disappeared right after it still fails, with an
honest "no device detected downstream" message instead of a fabricated
speed reading.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
pcie-nvidia-link.txt, pcie-nvidia-link-under-load.txt, and
kernel-aer-nvidia.txt only ever lived in supportBundleCommands, which
exclusively runs inside the on-demand "Download Support Bundle" web UI
action. The blackbox USB auto-sync worker never calls that function -
it only mirrors whatever CaptureTechnicalDump already wrote into the
live export tree at boot. So these three files were structurally
unreachable from a blackbox pull no matter how fresh the build was;
earlier analysis of a real blackbox misattributed their absence to
build/version drift instead.
Move the underlying scripts into shared exported constants
(platform.PCIeNvidiaLinkScript, PCIeNvidiaLinkUnderLoadScript,
KernelAERNvidiaScript) and add them to techDumpNvidiaCommands, so
CaptureTechnicalDump captures all three once at boot (bee-audit is
oneshot, so the ~8s bee-gpu-burn cost for the under-load sample is a
one-time boot cost, not a per-sync-cycle one) alongside the existing
nvidia-smi-* dumps. supportBundleCommands still re-runs the same
scripts on demand for a fresher sample - that's intentional, not a
duplicate to clean up.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
NVIDIA GPUs deliberately downclock PCIe to Gen1 at idle for power
saving, and applyPCIeLinkSpeedWarning fired on every idle collector
pass regardless - since component-status DB records never downgrade
(Record() only ever raises severity), one boot-time idle sample
permanently pinned pcie:gpu:nvidia to Warning for the rest of the
session even after every load-bearing GPU SAT test passed clean. Two
prior fixes (nvidia-smi-sourced link speed, pcie_aspm=off boot flag)
didn't hold up against this hardware/driver combination - see
bible-local/decisions/2026-08-24-pcie-gpu-gen1-idle-warning.md for the
full history.
Rather than add a downgrade path, stop writing an unverified status in
the first place: parseLspciDevice no longer calls
applyPCIeLinkSpeedWarning on the idle path. LinkSpeed/MaxLinkSpeed stay
populated as plain descriptive fields; only a verified-under-load
caller may now turn them into a status verdict.
Two new SAT targets provide that verified signal:
- pcie-link (platform/pcie_link_check.go): forces every enabled PCIe
device - not just GPUs - to retrain via the PCIe spec's Link Control
"Retrain Link" bit, then compares the negotiated speed against the
device's max. Covers NICs/HBAs/switches that have no bee-gpu-burn
equivalent load tool. Classifies by PCI class code + vendor ID, not
name substrings. Routes gpu_nvidia/gpu_amd/other sub-verdicts into
their own component-status keys so a degraded NIC never reads as a
GPU fault.
- nvidia-pcie-bandwidth (platform/nvidia_pcie_bandwidth.go): drives
real host<->device traffic via dcgmi diag -r nvbandwidth and
resamples link speed immediately after, independent of nvbandwidth's
own pass/fail.
Both wired into the task queue/webui the same way as nvidia-config
(routes, dispatch, priority, Validate page cards, Run All Check SAT).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
A CPU that had thermally throttled (sysfs thermal_throttle counter >
0) still reported status "OK" everywhere: dmidecode-derived CPU status
only distinguishes populated/enabled/disabled and never looked at the
throttle flag the collector already recorded next to it, and neither
SAT path meant to catch this actually could:
- The routine "cpu" SAT pack (RunCPUAcceptancePack) only checked
lscpu/sensors/stress-ng exit codes — stress-ng exits 0 whether or
not the CPU throttled while running it, so an 89°C/throttled CPU
right after a "successful" run still showed cpu:all as OK in
component-status.json.
- The more thorough platform-stress test already detected throttling
and fan-spindown correctly, but wrote its verdict as "Overall: FAIL
— ..." with no "=", which parseSATKV can't parse — so even a real
detected throttle event never reached the component-status DB.
Fixes:
- cpu_telemetry.go: escalate a CPU's status to Warning (only-escalate,
same severity ranking already used elsewhere) when Throttled is set.
- sat.go: add a before/after thermal-throttle-counter check job around
the "cpu" pack's stress-ng run, so a throttle event during the run
fails that job and (via the existing FAILED->Warning DB mapping)
flips cpu:all to Warning.
- platform_stress.go: emit a machine-readable overall_status= line
alongside the human-readable verdict so platform-stress results
actually reach ApplySATResultToDB.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
nvidia-bug-report.sh appends .gz to --output-file when gzip is available,
which silently produced empty nvidia-bug-report.txt in support bundles
(cat looked for the uncompressed name that never existed).
Also: a GPU that falls off the PCIe/NVLink bus (Xid 79) or gets flagged
for Node Reboot Required (Xid 154) mid-SAT-run left every downstream test
failing with generic, unrelated-looking errors (CUDA "unknown error",
"unable to determine device handle") with no indication the GPU needed a
physical power-cycle to recover. Detect these codes from SAT run logs and
surface a plain-English "physical reboot required" message in the task's
failure detail, the persisted component-status DB, a dashboard banner on
the Hardware Summary card, and topology diagram GPU-node severity.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
- page_scenario.go: onclick built via JSON.stringify() embedded raw double
quotes inside a double-quoted HTML attribute, truncating the attribute so
the click handler never compiled; pass the name through an escaped
data-scenario-name attribute instead.
- build.sh: overlay staging rsyncs (OVERLAY_DIR->stage, stage->includes.chroot)
ran without --delete, so a scenario removed from the repo (a9924b0) stayed
baked into every ISO built from the persistent stage cache since — the
"second script" in the Scenario page's list.
- blackbox: rewritten around a deterministic local zip + incremental
patch-the-changed-suffix onto removable media, instead of walking/copying
~90 files through a synchronous ntfs-3g FUSE mount every cycle. journalctl
captures are now "--since last sync" (were "--since boot", growing with
uptime) and metrics.db is excluded (was copied whole every cycle).
- scenario: nvbandwidth-acs-ab now escalates GPU count (same-socket pair,
other socket's pair, one cross-socket pair, all GPUs) under each ACS state
instead of always running all 6 GPUs at once, using a new `bee
gpu-bandwidth-groups` subcommand that discovers socket layout from
`nvidia-smi topo -m` at runtime — gpu_indices is host-specific, so this
can't be baked into the scenario file.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
ScenarioSpec gains an optional "description" field. Listing (both
ListLocalScenarioFiles and ListScenarioFilesOnRemovableMedia, via the new
scenarioDescription helper) reads it out of each file without requiring
full ParseScenarioJSON validation to succeed, so a listing never hides a
scenario over an unrelated validation issue. The webui Scenario page now
renders Name/Description/Found-on/Run instead of just Name/Found-on — a
bare filename rarely tells anyone but the author what a scenario actually
does.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
platform.LocalScenariosDir (/usr/share/bee/scenarios, populated from
iso/overlay/usr/share/bee/scenarios/ by build.sh's overlay rsync) is now
checked before removable media for both `bee run <name>` and the "6.
Scenario" page — a scenario shipped with the image works with no USB
stick required. ReadScenario/ListAvailableScenarios merge local + USB;
the removable-media-only functions from the previous commit are kept
as-is (still used directly where that's actually what's wanted) rather
than renamed out from under existing callers/tests.
iso/overlay/usr/share/bee/scenarios/nvbandwidth-all-gpu-power-watch.json
is a copy of scenarios/nvbandwidth-all-gpu-power-watch.json — the two
aren't auto-synced (documented in scenarios/README.md), so shipping a
scenario baked-in means checking it into both places.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Exposes the scenario engine (platform.System.RunScenario, added earlier)
in the web UI instead of only the `bee run` CLI: a new nav item lists every
scenarios/*.json found on mounted removable media (GET /api/scenario/list)
and runs one with a click (POST /api/scenario/run), enqueued as a normal
Task with target "scenario" — progress/logs live in Tasks like any other
SAT pack, no separate live-output UI needed.
- app.go: satRunner gains RunScenario, exportManager gains
ListScenarioFilesOnRemovableMedia/ReadScenarioFromRemovableMedia — both
already implemented on platform.System, just newly exposed through App.
- webui/tasks.go: taskParams.ScenarioName; runTask's "scenario" case reads
the file from removable media, parses it, and runs it.
- webui/page_scenario.go: the page itself.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Investigating the CG480-S6053 reboot needed a way to run an ad-hoc load
(nvbandwidth across a specific GPU set) while sampling IPMI/nvidia-smi
telemetry in the background — without hardcoding a one-off test into the
SAT pack code for a single investigation.
- audit/internal/platform/scenario.go: ScenarioSpec/ScenarioJob (JSON,
no new dependency) + System.RunScenario. "command" jobs run sequential
or parallel (per-job "parallel" flag); "sampler" jobs run concurrently
in the background on their own interval until every command job
finishes or the scenario's timeout elapses. "{{gpus}}" in a command's
cmd is substituted from that job's gpu_indices. Command jobs are wired
through the same satJobBoundaryHook/satSyncBracketHook seams the SAT
job runner uses, so a scenario run gets the same durability treatment
(evidence that a risky command started/finished reaches blackbox before
a possible crash, not just whatever streamed to the RAM-backed export
dir).
- export.go: ReadScenarioFromRemovableMedia mounts each removable target
looking for scenarios/<name>.json — an air-gapped engineer can author a
scenario elsewhere, drop it under scenarios/ on the same USB stick
already plugged in for blackbox, and run it with no network path onto
the host.
- cmd/bee: new `bee run <file.json|name>` (bare name = looked up on
removable media); `bee scenario run <arg>` kept as a longer alias.
- scenarios/nvbandwidth-all-gpu-power-watch.json: the scenario that
reproduced the actual reboot (full nvbandwidth across all GPUs, which
crashed, vs. clean per-socket passes), with IPMI sensor + GPU power/temp
sampling for a power-delivery correlation check.
Also: webui/page_topo.go — the /topo page's component-status-detail modal
(GET /api/component-detail/{type}) showed "No status data recorded yet"
for any component type ComponentStatusDB has no history for yet (e.g. GPU
before a SAT run this boot), even though the topology card for the same
component already showed "N OK" from the audit inventory snapshot.
inventoryFallbackRecords now synthesizes records from that same inventory
snapshot when StatusDB is empty, using the same device classifiers
(isGPUDeviceClass etc.) and severity mapping (classifyTopoSeverity) the
topology card itself uses, so the two views never disagree.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Replaces the flat export/ + techdump/ + system/ + systemd/ layout (two
same-named-but-different techdump/ dirs, disk reports duplicated between a
SAT run dir and techdump/) with one shared categorizeExportTree used by both
BuildSupportBundle and the blackbox USB mirror:
- export/{cpu,memory,storage,gpu,network,platform}/ — raw vendor-tool
output grouped by device type, plus export/reanimator.json ready to POST
to Reanimator's /ingest/hardware endpoint.
- status/ — computed diagnosis (component-status.json, runtime-health.*,
and metrics.db, previously missing from every bundle entirely).
- tasks/ — bee's own task-run bookkeeping (bee-sat/, bee-bench/, task
reports, service logs) where duplication with export/ is expected.
- livecd/{gui,host}/ — live-boot/kiosk-session-only diagnostics, kept out
of the hardware-facing tree.
Drops the redundant disk-report mirror write in RunStorageAcceptancePack
and the now-dead syncDirectoryTree/removeMissingPaths; adds a size+mtime
skip in copyPath so the blackbox mirror doesn't rewrite unchanged files
every cycle. README.md rewritten to match.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
- gpuBandwidthSocketGroups: a single GPU whose NUMA node fails to resolve
no longer collapses the whole per-socket nvbandwidth split into one
fallback pass — it now folds into the last resolved group instead,
preserving isolation for the sockets that did resolve.
- blackbox discoverMarkedTargets: skip mounting/unmounting devices that
already have a running worker on every 2s discovery tick. This was
observed hammering the same USB target continuously (mount+unmount
every ~2s for the whole session) and contending with the worker's own
sync cycle, plausibly explaining multi-minute sync cycles seen on a
real crash bundle.
- syncFilesystem now calls syscall.Sync() directly instead of spawning
/bin/sync per copied file; blackbox mounts removable targets with
-o sync so writes are durable without relying on the app-level sync as
the primary mechanism.
- New platform.SetSyncBracketHook / satJob.syncBracket: blocks (with a
bounded timeout) on blackbox actually reaching removable media right
before and right after a diagnostic's real load step (nvbandwidth,
memtester, stress-ng, dcgmi diag, nccl, smartctl/nvme self-test...),
instead of only firing a fire-and-forget kick after the job's own log
file is written. A crash mid-load now has durable evidence the load
started, not just whatever streamed to the RAM-backed export dir before
blackbox's next scheduled cycle.
Found investigating a real support bundle where blackbox's last
successful sync (19:55:25) predated both the previous job finishing and
the crashing nvbandwidth job starting (19:56:57) — none of the crash
window ever reached durable media.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
A crash mid-command (e.g. the nvbandwidth reboot) previously lost that
job's entire output: streamExecOutput only buffered stdout/stderr in
memory and the job's log file was written once, after the process
exited. It now also streams each line straight to that file as it
arrives, so whatever printed before a crash survives.
Root filesystem here is a tmpfs overlay (toram boot), so the only real
persistence boundary is blackbox's mirror to removable media, not the
local write itself. platform.SetJobBoundaryHook lets app wire a touch
of a small kick-file after each job's output is written; blackboxWorker
now polls that file's mtime alongside its normal adaptive timer and
syncs immediately on a kick instead of waiting out the current flush
period (up to 30s).
On multi-socket systems, run the NVIDIA bandwidth diagnostic once per
CPU socket before the all-GPU pass, so a crash confined to the all-GPU
run (with clean per-socket passes preceding it) isolates a cross-socket
peer-to-peer fault instead of leaving it conflated with a general
GPU/PCIe issue. Single-socket systems keep the original one-pass shape.
Also expand the support-bundle README with reference notes distilled
from a real analysis pass (BMC clock drift, "0/empty" tool output
meaning absent hardware rather than a fault, timestamp-matching before
assigning causality, and a normal-power-cycle SEL signature), plus a
step-by-step recipe for diagnosing an unexpected reboot/crash during a
specific test.
Storage acceptance runs already write disk-<prefix>-report.txt (per-drive
health + pseudographic resource bars) into the timestamped bee-sat run dir.
Also mirror it into techdump, a sibling of baseDir under the same export
dir, so a support bundle surfaces these reports alongside the rest of the
diagnostics without anyone having to dig into a specific bee-sat run dir.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Every place that surfaced a FAILED SAT result — task error messages,
component-status.json detail, and the hardware snapshot's ErrorDescription/
StatusHistory — used to say only "SAT overall_status=FAILED (see
summary.txt)" or "<label> failed", forcing an engineer to go dig through the
run directory to find out what actually broke.
nvidia-config's summary.txt now carries a "warnings" field with the specific
GPU/NVLink finding. A new SATFailureDetail/satFailureDetailFromKV in
component_status_db.go reads that field, or falls back to naming whichever
generic SAT sub-job(s) reported non-OK/UNSUPPORTED status along with their
exit code. This feeds both the task-runner error message and the component
status DB. sat_overlay.go's satKeyStatus (which drives ErrorDescription on
the exported hardware snapshot) now does the same, with storage kept
per-device so one drive's rc doesn't get attributed to another's card.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The standalone "confidential-computing" SAT target only ever checked CC
readiness, which most fleets never opt into (a NOT_READY verdict there
isn't a fault). Meanwhile DCGM diag never asserts GPU config compliance
(ECC/MIG/power-limit vs factory default) or NVLink topology (per NVIDIA's
own DGX BasePOD deployment guide, this needs a separate validation step)
— gaps confirmed against public DCGM docs and a real NV17-vs-expected-NV18
bonded pair found on a live bundle.
Repurposes the routine into "nvidia-config": reuses the existing
ListNvidiaGPUSettings() (already backing the GPU-settings page) to flag
ECC disabled, a MIG mode change stuck pending a reset/reboot, and a power
limit capped >5% below default; parses "nvidia-smi topo -m" bonded pairs
against "nvlink -s/-e" to flag any inactive lane or nonzero replay/
recovery/CRC counter on an otherwise-active bond. CC readiness is folded
in as one informational field (does not gate overall_status) rather than
a dedicated test. Reports under the same pcie:gpu:nvidia severity key as
every other nvidia-* SAT target instead of an isolated key, so a
config/NVLink FAILED result isn't invisible next to stress-test results.
Also fixes ApplySATResultToDB silently dropping any target with no
matching switch case (exactly what the old confidential-computing target
did) with a new coverage test enumerating every real SAT target.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
/topo blocked the HTTP request on live nvidia-smi calls with no timeout
(topo -m, nvlink -s/-e run on every page load), so a wedged driver hung
the page indefinitely. CaptureTechnicalDump now persists these dumps
once per audit cycle; the page reads them from techdump/ instead.
buildSocketIndex mapped NUMA node number to CPU by treating dmidecode's
Socket Designation (often 1-indexed, "CPU1"/"CPU2") as equal to the
NUMA node number (always 0-indexed) — GPUs/NICs on NUMA node 0 fell
into the "unknown" column, others attached to the wrong CPU box. Now
ranks CPUs by Socket value instead of assuming a shared numbering base.
Fixed a bug in ComponentStatusDB/applyComponentStatusDB where GPU SAT
results were keyed per-target ("pcie:gpu:nvidia-stress") instead of
per-vendor, which both broke cross-tier severity tracking (a later
clean "2. Check" run and an earlier failing "3. Load" run never
compared severities) and silently failed to match any real BDF, so the
DB overlay never reached the topology graph at all. GPU keys are now
normalized to vendor ("pcie:gpu:nvidia"/"pcie:gpu:amd"). Also skip
writing to the DB when a SAT task was aborted by the user (ctx
canceled), so a partial run can't stomp a previously recorded status.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Covers the sat.go fix from 2599d9c: a failing "dcgmi discovery -l"
preflight job must not flip the pack's overall status, and jobs marked
with retries should recover from a transient first-attempt failure.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Adds a GPU Settings card to /tools for the settings that actually
persist on NVIDIA data-center GPUs: ECC mode, MIG mode, and
Confidential Computing mode (all stored in the GPU's inforom/firmware,
take effect after a GPU reset or reboot) plus power limit (does not
persist — reapplied on demand). Includes a one-click "Reset All to
Defaults" that restores factory settings across every visible GPU,
touching only whatever has actually drifted.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
dcgmi discovery -l is a preflight/metadata step ahead of the real DCGM
diag jobs; a transient failure racing nv-hostengine startup shouldn't
flip the whole pack's status, so it's now marked informational with a
couple of retries. Separately, bound the fabricmanager/nvidia-dcgm
systemctl restart/start calls in bee-nvidia-load with a timeout so a
wedged unit (e.g. fabric training stuck on a bad NVSwitch fabric)
can't hang bee-nvidia.service forever and block dcgm from ever
starting.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
storcli64 enumerates these controllers but reports zero drives; storcli2
is the tool Broadcom ships for Tri-Mode/MegaRAID8 hardware and uses a
compatible JSON schema for drive listing. Wires storcli2 into both the
collector (structured drive data) and the webui RAID Management page
(dedup so a controller isn't double-listed if storcli64 already sees it
with zero drives), plus techdump raw collection and the ISO vendor-tool
build step.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
New read-only visualization page: CPU sockets as anchor nodes, PCIe
devices (GPU/NIC/RAID) linked to their NUMA-affine socket with edge
color derived strictly from link_speed vs max_link_speed (not from the
device's own Status, which can also be overwritten by SAT-test results
on the same field), PSU/BMC as standalone boxes with no connecting
line, and a separate NVLink Topology card (live nvidia-smi topo -m /
nvlink -s/-e queries, not persisted to any contract).
GPU-GPU edges are drawn strictly from the actual bonded-pair list
parsed out of "nvidia-smi topo -m" (parseGPUPairAdjacency), not from
adjacent box position in the layout — an earlier ASCII mockup drew a
"chain" through unrelated GPUs, which a dedicated regression test now
guards against. A bonded pair spanning two different NUMA nodes is
flagged Warning on the edge and on both GPU boxes, per project
decision that this is an anomaly worth surfacing, not a neutral fact.
Zero changes to the ingest contract: this reverts the HardwareNVLinkPort/
HardwarePCIeDevice.NVLinks field shipped in v11.55 (33d6eee) along with
its collector/nvidia.go enrichment — that field risked a 400 from
Reanimator Core's strict decoder without an RFC, and isn't needed since
the topo page queries nvidia-smi directly instead of reading it from
audit.json. The v11.55 systemd fix (bee-nvidia.service ordering,
nv-hostengine restart) and the nvlink-status/-errors/dcgmi dumps in the
support bundle are untouched.
Also reorganizes support bundle collection per project convention:
system/ is now LiveCD-operational logs only (Xorg, services, console,
network/FS of the host itself); all server-hardware dumps (lspci,
NVIDIA/NVLink/DCGM, fabric manager, PCIe AER, ethtool, mstflint) move
to techdump/, deduplicating two entries already produced by
platform/techdump.go. Adds nvidia-bug-report.sh (previously only
collected inside the NVIDIA SAT pack) and lscpu to the always-on dump.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
dcgmi diag's failures only surface a terse wrapper message ("Detected
driver major version 0 is not between the required versions 346 and
2000"), which doesn't say why. Reading DCGM's own nvvs source
(NvidiaValidationSuite.cpp::CheckDriverVersion) shows this fires when
dcgmSystem.GetDeviceAttributes(0, ...) comes back empty — the version
string is never actually malformed. Diagnosing further requires info
bee never collected: whether dcgmi discovery even sees GPU 0/1
correctly, and nvvs's own internal debug log (normally
/var/log/nvidia-dcgm/nvvs.log, which bee never captured).
Add a "dcgmi discovery -l" job before every DCGM diag invocation
(check-gpu-dcgm-l2, nvbandwidth, targeted_power, pulse_test,
targeted_stress), and route dcgmi diag through
"-v -d DEBUG --debugLogFile {{run_dir}}/..." so the full nvvs debug
log lands in the SAT run dir and gets picked up by the support bundle
automatically, instead of needing a live SSH session on hardware we
usually can't get a second look at.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
New read-only "Check" step reports whether this server can run NVIDIA
Confidential Computing: CPU TEE support (Intel TDX / AMD SEV-SNP, via
dmesg and kvm_amd sysfs params) and GPU firmware CC capability (via
`nvidia-smi conf-compute -q`). Also collect that command's output into
the techdump export bundle.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Disk report now ends with a Conclusion section judging a drive NEW/USED
against loose thresholds (<110% capacity written, <210% read, <7d
uptime, <30 power cycles), listing which ones tripped. Data
Written/Read in the Usage section now scale to TB/PB via
formatBytesHuman instead of always printing raw GB. storageSATCommands
now runs smartctl with -i so SATA/SAS reports get Model/Serial/
Firmware/Capacity, which the Conclusion needs to evaluate the
write/read criteria (previously only -H -A was collected).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
nvme-cli emits large 64-bit counters as JSON-quoted strings on some
versions; the disk-report text generator only handled bare numbers and
{lo,hi} objects, so power_on_hours/data_units_read/data_units_written
etc. silently parsed as 0 while the structured collector path already
handled this correctly. Unify both paths on a single exported
JSONInt64/NVMeSmartLog/NVMeIDCtrl type in collector/storage.go instead
of keeping two independent nvme-cli JSON parsers in sync.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Ramp Sequence table's Run 1 row showed "—" for GPU power because the
step-1 fast path (reusing single-card calibration) never populated
PerGPUTelemetry like steps 2+ do. Also add GPU total W / Server itself W
columns and an idle baseline row so server-vs-GPU consumption is visible
per ramp step.
smartctl -t short only launches the self-test and returns immediately
("Testing has begun"); unlike nvme device-self-test --wait, it has no
blocking mode. Validate/Load runs closed the task and produced reports
before the drive actually finished the test. Now poll smartctl -a until
the test completes (or times out) and report the real result.
Also add a per-disk "Resource" section with pseudographic progress bars
for uptime (vs 5y design life), bytes written (vs 1 DWPD x 5y budget),
and bytes read (percent from SMART attribute 242), all rendered in
human-scaled units (days/years, TB/PB) instead of raw hour/byte counts.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Check mode: read-only SMART/NVMe data collection, no self-test.
Load mode: same collection + short self-test (nvme device-self-test -s 1,
smartctl -t short). Card descriptions updated accordingly.
After each storage SAT run, a disk-N-devname-report.txt is written
per device into the runDir (auto-included in support bundles).
Web UI task page renders one card per disk directly below Task Report.
Also fixes pre-existing TestDashboardRendersRuntimeHealthTable failure:
test fixture used "inactive" status but code now treats inactive as OK
for completed oneshot services; updated to "failed" to match intent.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- sat.go: DetectGPUVendor lspci fallback now checks GPU device classes
([0300]/[0302]/[0380]) per line instead of scanning the whole output for
vendor name; AMD EPYC servers have dozens of AMD-branded PCIe entries
(Root Complex, IOMMU, Host Bridge) that were triggering the old check
- blackbox.go: fix deadlock in finishCycle — it held w.mu while calling
persistState(), which acquires rt.mu then re-acquires w.mu inside
persistStateLocked(); now w.mu is released before persistState()
- build.sh: remove NVIDIA-specific overlay files (bee-gpu-burn,
bee-john-gpu-stress, bee-nccl-gpu-stress, bee-nvidia-recover,
bee-dcgmproftester-staggered, bee-check-nvswitch,
nvidia-fabricmanager.service.d/) for non-nvidia build variants
- bee-selfheal: gate NVIDIA recovery on BEE_GPU_VENDOR=nvidia so the
script does not attempt to restart bee-nvidia.service on NOGPU builds
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- audit JSON: IPMI sensor readings (ipmitool sensor) merged into hardware.sensors alongside lm-sensors data
- audit JSON: IPMI SEL entries (ipmitool sel list) in hardware.event_logs with source "ipmi-sel"
- audit JSON: dmesg error/warning lines in hardware.event_logs with source "dmesg" (filtered by error/warn/AER/Xid/NVRM/ECC/panic patterns)
- support bundle: added ipmitool-sensor.txt, ipmitool-sel.txt, ipmitool-sel-time.txt to techdump
- saa_dmi.go: fix dmiItemRE to accept SHN with parentheses (e.g. PS(4)LC for PSU fields)
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
